Birel Art N35 RS

Manufacturier
Birel ART
Modèle
N35 RS
No de produit :
B-N35-RS
7 195,00 USD

The N35-RS model has been designed to be at the top of the rental kart market. 

 
It weights 150kg, which is about 30 kilos less than the competitors. It allows a better fuel economy and increase tyre life. It also reduces maintenance and running costs as well as ensuring greater reliability.
 
The moving parts, engine and cables are protected with a complete bodywork covered in an elegant and futuristic artwork which design is inspired by competition karts.
 
With its rapid fixing system, the bodywork can be easilly removed: it is made up of five quick-fit screws and a quick release steering wheel. The cover has been designed to enclose the entire front and rear of the chassis, creating a survival cell around the driver and increasing the safety. In order to limit damage to the kart's wheels and mechanical parts, fenders are attached to the chassis with rubber inserts to isolate them from the chassis structure. The bodywork is made from memory system plastic, designed specifically to withstand and absorb impacts of over 10G. The chassis is made of Ø 35x2mm chrome-moly tubing, with additional strengthening at key points which design is inspired from experience gained in racing.
 
A very new element in the Rental Market is the removable steering wheel; it has been studied in order to allow an easier removal of the complete covered bodywork, thanks to the removable steering wheel hub, as used in single-seater race cars.
 
The steering system is composed of spindles made of cast stainless steel body, with a pressed lever and a removable wheel axle. Steering tie rods are made out of a special plastic material with aluminum bushings to fix uniball. Each front wheel is mounted on four bearings to reduce axle load as much as possible. There is an angled steering wheel support made of aluminum. 
 
The kart has a 12-litre tank with automotive type bayonet fitting for easy refueling, accessible via a flap on the top surface of the bodywork.

It features an adjustable positioning of the seat and pedals. The seat is mounted to a steel frame on runners allowing a displacement of 80mm. The pedal box can be adjusted manually or activated by a lever on the right side of the seat, which can be operated by the driver. It has a movement range of 30mm.

A new SDBS (Slowing Down Brake System), which comes into action during braking, reduces the speed of the vehicle by operating on the throttle return cable. The go-kart can be fitted with the new exhaust, designed by Birel ART with the aim of increasing performance and reducing both CO2 emissions and noise.

The brake system is composed of a master cylinder with a separate fluid reservoir above the cylinder. A caliper with two pistons with road-car derived pads makes the system lasts longer: it works on stainless steel runners to reduce friction and increase mileage. Nylon brake lines are manufactured to aeronautical standards, they are made of braided stainless steel hose to withstand over 1000 bar pressure. 180mm steel disc is fitted to a fully machined aluminum caliper.
 
The Axle is made of chrome-moly steel, mounted on four bearings. Rear hubs are made from fully machined aluminium, which are fixed with an 8 mm key that blocks the hub.
 
The karts can also be fitted with exhaust silencers made for the Honda GX 200-270-390. They are designed to increase performance and reduce both CO2 emissions and noise.

Partager ce produit :

Spécifications techniques

WEIGHT: 150 kg

TUBES DIAMETER 35mm

WHEEL BASE: 1070mm

REAR WIDTH: 1410mm

FRONT WIDTH: 1208mm

LENGTH: 2036mm

AXLE: 40x5x1080 K

BRAKING SYSTEM: HYDRAULIC RR

BRAKE POSITION: REAR

TANK CAPACITY: 12L

STEERING WHEEL DIAMETER: 320mm

WHEELS: CH 120 or 130 DH 180

TYRES: VEGA RH8 manufactured for Birel ART

PODS: N 35 RS

BACK COVER: FULL COVERED BODYWORK

SEAT: ADJUSTABLE SYSTEM

PEDAL: ADJUSTABLE SYSTEM